Prevent Diskpace Monitor from sending alerts (alert emails)
How do you prevent the diskspace monitor from sending alerts via email? I still need it to be monitored because I need to generate a report but can't have alert emails sent out. I have approximately...
View ArticleClik here to view.
Error rendering last xx Syslog messages
So I have at least one Windows Server node that shows the Syslog module in its view (not sure why, as it's not sending Syslogs to NPM) that shows this within that module: There was an error rendering:...
View ArticleClik here to view.
how to reduce the size of the log files.
how to reduce the size of the log files.core_businessLayerPlugin_tracelog.syslog npm_businessLayerPlugin-bracelog.syslog
View ArticleRe: Prevent Diskpace Monitor from sending alerts (alert emails)
Hello Brink668, Within the settings page for the Drive Space Monitors, set the "Maximum Alerts to Send" to 0 and/or "Accumulated failures per Alert" to 999999. Hope this helps. Sincerely, Chris Foley
View ArticleRe: Prevent Diskpace Monitor from sending alerts (alert emails)
Do I have to do this for each diskspace monitor? Is there a way to set this as the default monitor settings?
View ArticleHost Partition Storage Free Space Alert Problem
We have Virtualization Manager running in our environment and i'm having a strange issue with it. One of the alerts that comes up is in regard to Host partition storage free space. It states that if...
View ArticleClik here to view.
ESX Status Question
We have some of the ESX Hosts showing up gray (not green or red) in NPM (IVIM). I am able to run the credential test and that comes back fine, but when I drill into the node and look at the ESX Status...
View ArticleRe: track nodes by group name?
This thread has some good comments for a similar question:Re: NPM Group alert The suggestion there is either to use Custom properties (as said above), or to configure a Group Member alert (rather than...
View ArticleClik here to view.
How to set up an account to monitor Windows 2012 domain controllers that is...
This seems like something that must be out there already but I've been googling and searching thwack and can't find it. I am looking for a step by step walk through for setting up an account to use in...
View ArticleRe: False APC UPS reboot messages
I would check out the uptime counter for a rollover. APC 'False' Reboot Alerts -ZackMLoop1 Systems: SolarWinds Training and Professional ServicesLinkedIN: Loop1 SystemsFacebook: Loop1 SystemsTwitter:...
View ArticleRe: File Monitor in NPM
This function is not available in NPM. I would instead recommend looking at Server & Application Monitor, which fully integrates with NPM.
View ArticleRe: Can you load Dell OMSA hardware sensors on linux in Orion?
Yes. SAM supports monitoring the hardware health of Dell PowerEdge, HP Proliant, and IBM X-Series server running either Windows or Linux. If you installed OMSA under Linux and the node is managed via...
View ArticleRe: What We Are Working On
Cisco is dropping java from their GUI interfaces . All new code is html5 based or core when will sw step and move to current best practices ?
View ArticleRe: What We Are Working On
Posted this 9months ago no repose from sw yet anyone watching this channel?
View ArticleClik here to view.
Re: File Monitor in NPM
Hi There,I think the tricky bit will be setting something up to look within the file. Just to throw another option out there we have a system called LANGuardian which uses network traffic as a data...
View ArticleRe: NPM Group alert
rob.hock wrote: If you want to use groups, you could configure a group member alert to alert on group member status going down.Haven't been able to figure this out, and looks like I am not alone. There...
View ArticleRe: track nodes by group name?
mrd0000 wrote: This thread has some good comments for a similar question:Re: NPM Group alert The suggestion there is either to use Custom properties (as said above), or to configure a Group Member...
View ArticleRe: track nodes by group name?
Recommendation is to use the Custom Property Manager to create a Custom Property at the Node level and assign values to that Custom Property in order to group the nodes by Custom Property value instead...
View ArticleClik here to view.
Re: SW npm 10.6 upgrade to 10.7 ??
The Database has been backup up and the installer is still hanging on the "Backup Database Type "YES"" section. By the way, name is Eric.
View ArticleRe: Resources Report
Didn't think of that. Will make do with the report you attached earlier. Thanks!
View Article